So… Tube Mods – Battery positive end up or down? – Mech Mods

So… Tube Mods – Battery positive end up or down?

http://ift.tt/2mBVs55

Firstly, let me say I know the answer to the basic question, but I want to get people’s views on mitigating risk factors.

In a hybrid tube, generally, the battery should go positive up, so the positive pin on the RDA connects with the positive connector on the battery. The body of the tube is therefore negative and the circuit is only completed if you press the switch, connecting the negative end of the battery with the negative body of the tube.

That way around, if there is any unnoticed…

So… Tube Mods – Battery positive end up or down?

Planet Of The Vapes Forum

via Mech Mods http://ift.tt/2j23cvf

January 13, 2018 at 06:00PM

Advertisements

Pinning down a short – Mech Mods

Pinning down a short

http://ift.tt/2mbL96O

So I’m a little lost on this one and needing a touch of advice

Got a goon 1.5 clone with a broadside clone for 20700s (since I needed some of those batteries anyway why not add a new mech to the collection)

But a week in I have an obvious arc mark inside the rda, including a well tarnished deck screw that matches placement wise to the arcing

Sounds simple enough but it’s turning out not to be

What I know (and have triple checked, starting simple)

Checked the coils

The coil reads…

Pinning down a short

Planet Of The Vapes Forum

via Mech Mods http://ift.tt/2j23cvf

January 9, 2018 at 05:39AM

Contact spark. – Mech Mods

Contact spark.

http://ift.tt/2qyzswi

I recently picked up a Hugo Squeezer it came with minimal fire contact sparking . I dismantled the device and cleaned It using a eraser. The arcing subsided though I’m not sure if this method is the most efficient for cleaning Mechanical devices. I picked up that trick working with old VW tail light harnesses. If any one has some tips or tricks I’d be happy to hear them.
View attachment 148718

Planet Of The Vapes Forum

via Mech Mods http://ift.tt/2j23cvf

January 8, 2018 at 05:36AM

Building on a Battle Deck – Mech Mods

Building on a Battle Deck

http://ift.tt/2E60Vaw

So my beauty turned up today

[​IMG]

And when it came to coiling it up I have been using Fused Claptons (0.45 Ohm) however when I cut them down, place on my ohm meter they come out at 0.56? Surely they would have been halved or am i wrong by the fact there is only one negative terminal?

Planet Of The Vapes Forum

via Mech Mods http://ift.tt/2j23cvf

January 4, 2018 at 05:28PM

Series mech – what are the best builds for them? – Mech Mods

Series mech – what are the best builds for them?

http://ift.tt/2E6Xr8u

I’m after a little help. I’m all up to speed with mechs, kinda know what I like and what I don’t like.

But I have just ordered an extension tube for my Subzero shorty, turning it into a series mech. I would just like some advice on what builds people use for 8.4v?

Using a dual coil on a mech I’m often at about 0.18-0.22ohms using some SS clapton type coils. I did think I could try a single coil rda with the same coil, meaning it would come in at 0.4ish ohms. Would this be a bit much…

Series mech – what are the best builds for them?

Planet Of The Vapes Forum

via Mech Mods http://ift.tt/2j23cvf

December 28, 2017 at 08:12PM

Best single coil rda – Mech Mods

Best single coil rda

http://ift.tt/2BKEuXS

righto chaps, I am looking for a single coil rda to find best flavour, needs to be 22mm, been looking at the hadaly as that seems to get some use on the squonkers, anyone got any suggestions ? It’ll be set up with a brochrome coil at 2.5mm id, prob around 0.4 ohm.

Planet Of The Vapes Forum

via Mech Mods http://ift.tt/2j23cvf

December 27, 2017 at 11:10PM